How To Remove Rear Tractor Tire From Rim

Download Article

Download Article

If you've got a tractor tire that is cut, damaged, or badly frayed, you can salvage the rim, and even the inner tube if information technology's in good condition, by removing the tire itself. To remove the tire from the rim, you'll need a few sturdy tools and a little scrap of elbow grease to get the job done. Debunk the tire so information technology'due south loose plenty for you to suspension the bead forth the rim. Once the seal is broken, yous tin work the rim out of the tire to remove it.

1. 1

   Locate the valve stem on the tire and remove the cap. Lay the tire flat on the ground and look for a small stem on the inside of the rim. Unscrew the cap from the stalk to betrayal the valve beneath it.^[ane]

   • Keep the tire laying so the stem is sticking upwardly.

2. ii

   Grip the middle of the valve with a pair of needle-olfactory organ pliers. Locate the small-scale rod on the inside of the valve stem, called a Schrader valve. Take a pair of needlenose pliers and insert them into the valve. Pinch the rod in the center of the valve and get a proficient grip on it.^[2]

   • If you lot have a valve stalk removal tool, yous can adhere that to the valve.
   • Don't squeeze the valve as well hard or you could crack or damage information technology.

   Advertisement

3. 3

   Rotate the valve counterclockwise to remove it and release the air. Once yous've got a stable grip on the Schrader valve, start turning it to unscrew information technology. Yous'll hear the air kickoff to be released from the tire. Continue rotating the valve until yous tin can fully remove it from the stem. Allow the air to flow freely out of the tire.^[3]

   • Set the Schrader valve bated so you don't lose the minor but important piece.

   Tire Tip: The air escaping the valve tin can cause it to shoot out of the stalk as information technology gets looser and then keep a firm grip with the pliers.

Advertisement

1. 1

   Mix together ii cups (0.47 50) of water and 1 teaspoon (four.9 mL) of dish lather. Fill a canteen, saucepan, or another container with warm water. Then, add the dish soap and stir or shake the mixture then it'south nice and soapy.^[four]

   • Standard dish soap will do the trick just fine.
   • Warm water will combine the mixture ameliorate and form more soap bubbling.

2. 2

   Lay the tire apartment and apply the mixture around the border of the rim. Place the tire on a flat surface such as a clear area of the ground or on concrete. Utilize the soapy solution around the tire where it connects to the rim to aid loosen the seal. Allow the mixture sit for a couple of seconds so it can penetrate beneath the rim.^[5]

   • Reserve some of the mixture for the other side of the tire later.

3. three

   Employ a sledgehammer or crowbar to suspension the dewdrop of the tire. The dewdrop of the tire refers to the seal where the tire connects to the rim. If you lot have a large tractor tire, employ a sledgehammer to strike the tire just above the border of the rim where they connect to interruption the bead. Keep hitting the tire around the entire circumference of the rim to break the seal completely.^{[half dozen]}

   • If you're using a sledgehammer, be very conscientious not to strike the rim or you could bend, paring, or crevice information technology.
   • For a smaller tractor tire, use the flat end of a crowbar to pry beneath the edge of the rim and break the dewdrop. Piece of work your fashion around the tire to break the seal all along the rim.

4. 4

   Flip the tire and break the bead on the other side. Once y'all've broken the dewdrop all along the rim of the tire and there aren't any sections still connected, grab the tire and flip it over. Pour the soapy mixture all along where the rim connects to the tire. Use a sledgehammer or crowbar to break the dewdrop along the rim.^[vii]

   • The rim should exist loosely attached to the tire once the bead is broken.

Advert

1. 1

   Lay the tire stem-side up and remove any basics from the rim. Afterward y'all intermission the dewdrop of the tire, lay it on a apartment surface then the valve stem on the rim is facing up. If in that location are nuts screwed onto the within of the rim, employ your easily or a pair of pliers to remove them so the inner tube can be taken out.^[8]

   • Set the nuts bated so yous don't lose them.
   • Not all tractor tires have nuts on the inside of the rim.

2. ii

   Wedge a crowbar where the tire connects to the rim to create an opening. Slide the flat end of a crowbar into the border where the tire meets the rim and pry the tire up to make an opening. Lay the crowbar flat across the rim so the edge of the tire is raised over the lip of the rim and held open up.^[9]

   Tire Tip: If the crowbar won't lay flat, stand on top of information technology or place a heavy object such every bit a brick or toolbox on top of information technology to hold information technology downwardly.

3. three

   Use some other crowbar to pry the residue of the tire over the lip of the rim. Once you've got the edge of the tire held open by the first crowbar, insert some other ane into the opening and work your mode around the tire to pry information technology over the lip of the rim. Continue effectually the entire circumference of the rim and so it's fully asunder from the tire.^[10]

   • After you've worked your away effectually the tire, the rim should no longer be attached to it.

4. 4

   Pull out the inner tube from inside of the tire. Use your hands to move the rim to the side and so you can meet the inner tube on the inside of the tire. Reach into the gap between the rim and the tire and catch the inner tube. Advisedly pull information technology loose from the tire and remove it.^[11]

   • If the inner tube doesn't have any tears or leaks, yous can reuse it.

5. 5

   Stand upwardly the tire and pull the rim out of it. Lift upward the tire so it's standing and take hold of the lip of the rim inside of it. Move the rim from side to side as you pull it to work information technology out of the tire. If the rim gets caught on the edge of the tire, apply a crowbar to pry it out.^[12]

Advert

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Things You'll Need

• Needlenose pliers
• Dish soap
• Sledgehammer (for large tractor tires)
• 2 crowbars

Virtually This Article

Thanks to all authors for creating a page that has been read 21,127 times.

Did this article help you?

Source: https://www.wikihow.com/Remove-a-Tractor-Tire-from-the-Rim

Share this post